VPort 354-SS-SC
Full Motion, 4-channel MPEG4/MJPEG Industrial Video Encoder, 2 single mode 100BaseFX Ethernet port, SC Connector, 0 to 60°C
Features and Benefits
- Industrial design with -30 to 70°C operating temperature and fiber optic Ethernet port
- 2 Ethernet ports for cascade and port redundancy
- SD card slot for local storage capability
- Modbus/TCP supported for easy communication with SCADA software
- Video stream up to 120 frames/sec at 4CIF (704 x 480) resolution
- Free VPort SDK PLUS supported
- -30 to 70°C wide operating temperature
- Built-in single-mode or multi-mode fiber optic Ethernet port—media converter not required
- 2 Ethernet ports for cascade and port redundancy
- 1 RS-232/422/485 COM port for controlling external serial devices over Ethernet (Pending)
- Redundant 12/24 VDC and 24 VAC power inputs for greater reliability
- Metal housing with IP30 protection against dust
- DIN-Rail mounting installation for industrial environments
- UL508 certification (Pending)
- Meets NEMA TS2, Section 2 requirements (Pending)
- Modbus/TCP for easy communication with SCADA software
- Standard RTSP (real-time streaming protocol) video streaming for easy integration
- Multicast (IGMP) protocols for efficient network transmission
- SNMPv1/v2c/v3 MIB-II for easy network management
- QoS (ToS) for configuring the transmission priority of video streams
- UPnP, DDNS, and IP filtering supported
Introduction
The VPort 354 is a high performance, 4-channel industrial video encoder that provides up to 4CIF full frame rate performance (NTSC: 704 x 480 @ 30 FPS; PAL: 704 x 576 @ 25 FPS) for each channel, and supports a dual MJPEG/MPEG4 algorithm, making it especially well- suited for use with distributed surveillance systems in critical industrial applications. In addition to the rugged-design features, the Modbus/TCP and serial-to-Ethernet connectivity make the VPort 354 more suitable for industrial applications. The two built-in Ethernet ports can be cascaded as a daisy-chain or used for port redundancy, making network communication more safe and reliable. To prevent video loss when the network is down, the VPort 354 can automatically record video on an SD card, and once the network is back up, the recorded video can be downloaded via FTP access.
Video
Video Compression: MJPEG or MPEG4 (ISO/IEC 14496-2)
Video Inputs: 4, BNC connector (1.0 Vpp, 75 ohm)
Video Outputs: Via Ethernet port
Video Streams: Dual streams (one for MJPEG, the other for MPEG4) at the same video resolution (note that MJPEG only has one quality setting)
NTSC/PAL: Manual
Video resolution and FPS (frame per second):
CIF:
NTSC:
Size: 352x240
Max. FPS: 30
PAL:
Size: 352x288
Max. FPS: 25
QCIF:
NTSC:
Size: 176x112
Max. FPS: 30
PAL:
Size: 176x144
Max. FPS: 25
2CIF:
NTSC:
Size: 352x240
Max. FPS: 30
PAL:
Size: 704x288
Max. FPS: 25
4CIF:
NTSC:
Size: 704x480
Max. FPS: 30
PAL:
Size: 704x576
Max. FPS: 25
Video Viewing:
Adjustable image size and quality
Timestamp and text overlay
Audio
Audio Inputs: 1 Line-in or MIC-in with RCA connector
Audio Outputs: 1 Line-out with RCA connector
Audio Format: Mono, PCM
Network
Protocols: TCP, UDP, HTTP, SMTP, FTP, Telnet, NTP, DNS, DHCP, UPnP, RTP, RTSP, ICMP, IGMPv3, QoS, SNMPv1/v2c/v3, DDNS, Modbus/TCP
Ethernet: 2 10/100BaseT(X) auto negotiating RJ45 ports, or 2 100BaseFX fiber ports (single/multi-mode, SC connector)
Serial Port
PTZ Ports: 1, RS-232/422/485 port (terminal block connector), max. speed of 115.2 Kbps
COM Ports: 1, RS-232/422/485 (DB9 female connector), max. speed of 115.2 Kbps
Console Port: 1 RS-232 RJ45 port
GPIO
Digital Inputs: 4, max. 8 mA
Low: +13 V to +30 V; High: -30 V to +3 V
Relay Outputs: 2, max. 24 VDC @ 1 A
LED Indicators
PWR1: Power 1
PWR2: Power 2
FAULT: Can be configured to correspond to system alarm, power failure, or disconnected network
V1, V2, V3, V4: Video input signal activity
Local Storage
SD Socket: Standard SD socket, SDHC, with SD LED indicator
Power Requirements
Input Voltage: 2 12/24 VDC or 24 VAC inputs for redundancy
Power Consumption: Approx. 12 W
Physical Characteristics
Housing: Metal, IP30 protection
Dimensions: 80.2 x 135 x 105 mm (3.16 x 5.31 x 4.13 in)
Weight: 1200 g (2.64 oz)
Installation: DIN-Rail mounting, wall mounting (with optional kit)
Alarms
Video Motion Detection: Includes sensitivity tuning
Video Loss: Video loss alarm
Scheduling: Daily repeat timing schedule
Imaging: JPEG snapshots for pre/trigger/post alarm images
Email/FTP Messaging: Automatic transfer of stored images via email or FTP with event-triggered actions
Custom Alarms: HTTP event servers and CGI events for setting customized alarm actions
PAN/TILT/ZOOM
PTZ Camera Control: Via RS-232/422/485 PTZ port or COM port
PTZ Control Function: PAN, TILT, ZOOM, FOCUS, moving speed, preset position (max. 25 positions), and 10 custom commands
PTZ Function Updates: Driver upload supported
Supported Device Protocols: Pelco D, Pelco P, Dynacolor DynaDome, Cohu, Custom Camera
Transparent PTZ Control: Control PTZ cameras with legacy PTZ control panel or keyboard connected to a PC or VPort decoder
Security
Password: User level password protection
Filtering: By IP address
Environmental Limits
Operating Temperature:
Standard Models: 0 to 60°C (32 to 140°F)
Wide Temp. Models: -30 to 70°C (-22 to 158°F)
Storage Temperature: -40 to 85°C (-40 to 185°F)
Ambient Relative Humidity: 5 to 95% (non-condensing)
Standards and Certifications
EMI: FCC Part 15 Subpart B Class A, EN 55022 Class A
EMS:
EN 61000-4-2 (ESD) Level 3,
EN 61000-4-3 (RS) Level 3,
EN 61000-4-4 (EFT) Level 3,
EN 61000-4-5 (Surge) Level 3,
EN 61000-4-6 (CS) Level 2,
EN 61000-4-8,
EN 61000-4-11
Shock: IEC 60068-2-27
Freefall: IEC 60068-2-32
Vibration: IEC 60068-2-6.
MTBF (mean time between failures)
Time: 271,000 hrs
Database: Telcordia (Bellcore), GB 25°C
Warranty
Warranty Period: 5 years
Software Development Kit
VPort SDK PLUS: Includes CGI commands, ActiveX Control, and API library for customized applications or system integration for third-party developers (the latest version of SDK is vailable for download from Moxa’s website).