ioLogik E2242-T MOXA serial remote io server

Features and Benefits

• Active communication with patented Active OPC Server
• Smart Alarm management with email, SNMP Trap, TCP, UDP
• Supports SNMPv1/v2c/v3 protocol
• Save time and wiring costs with peer-to-peer communication
• Front-end intelligent with patented Click&Go control logic, up to 24 rules
• Friendly configuration with web browser

Introduction

Moxa’s ioLogik E2200 is a new type of Ethernet micro RTU controller, which is a PC-based data acquisition and control device that uses proactive, event-based reporting to control I/O devices. Unlike traditional RTUs, which are passive and must poll for data, Moxa’s ioLogik E2200 series with Active OPC Server makes seamless connection with SCADA systems a reality. In addition, SNMP is used for communicating with an NMS (Network Management System) for IT field users. The I/O status of an Ethernet micro RTU controller can be reported and controlled automatically on-site based on user specified conditions. This report-by-exception approach, which is new to PC-based monitoring, requires far less bandwidth than traditional polling methods. The ioLogik E2200 Micro RTU supports simple and powerful Click&Go™ technology to deliver event-driven reports and allow alarm messages to be sent by email, TCP/UDP, and SMNP Trap with real-time stamps. With built-in Click&Go™ intelligence, the ioLogik E2200 micro RTU can be used for simple output control when it is triggered by input status, without the need for a PC controller. The ioLogik E2200 micro RTU reports I/O status automatically based on user-specified conditions. This report by-exception approach requires far less bandwidth than the traditional polling approach.

Inputs and Outputs

Analog Inputs: 4 channels
Configurable DI/Os: 12 channels

Analog Input

Type: Differential input
Resolution: 16 bits
I/O Mode: Voltage / Current
Input Range: ±150 mV, 0 to 150 mV, ±500 mV, 0 to 500 mV, ±5 V, 0 to 5 V, ±10 V, 0 to 10 V, 0 to 20 mA, 4 to 20 mA
Accuracy:
     ±0.1% FSR @ 25°C
     ±0.3% FSR @ -10 and 60°C
     ±0.5% FSR @ -40 and 75°C
Sampling Rate:
     All channels: 32 samples/sec
     Per channel: 8 samples/sec
     Single channel: 100 samples/sec
Input Impedance: 200k Ωs (min.)
Built-in Resistor for Current Input: 120 Ωs

Digital Input

Sensor Type: Wet Contact (NPN or PNP) and Dry Contact
I/O Mode: DI or event counter
Dry Contact:
     On: short to GND
     Off: Open
Wet Contact (DI to GND):
     On: 0 to 3 VDC
     Off: 10 to 30 VDC
Common Type: 6 points per COM
Isolation: 3k VDC or 2k Vrms
Counter Frequency: 900 Hz
Digital Filtering Time Interval: Software selectable

Digital Output

Type: Sink
I/O Mode: DO or Pulse Output
Pulse Output Frequency: 1 kHz
Over-voltage Protection: 45 VDC
Over-current Protection: 2.6 A (4 channels @ 650 mA)
Over-temperature Shutdown: 175°C (min.)
Current Rating: 200 mA per channel
Isolation: 3k VDC or 2k Vrms

Power Requirements

Power Consumption: 178 mA @ 24 VDC

MTBF (mean time between failures)

Time: 204,391 hrs
Database: Telcordia (Bellcore)

LAN

Ethernet: 1 10/100 Mbps RJ45 port
Protection: 1.5 kV magnetic isolation
Protocols: Modbus/TCP, TCP/IP, UDP, DHCP, BOOTP, SNMP, HTTP, CGI, SNTP, SMTP

Serial Communication

Interface: RS-485-2w: Data+, Data-, GND (3-contact terminal block)
Serial Line Protection: 15 kV ESD for all signals

Serial Communication Parameters

Parity: None
Data Bits: 8
Stop Bits: 1
Flow Control: None
Baudrate: 1200 to 115200 bps
Protocol: Modbus/RTU

Power Requirements

Power Input: 24 VDC nominal, 12 to 36 VDC

Physical Characteristics

Wiring: I/O cable max. 14 AWG
Dimensions: 115 x 79 x 45.6 mm (4.53 x 3.11 x 1.80 in)
Weight: under 250 g
Mounting: DIN rail or wall

Environmental Limits

Operating Temperature:
     Standard Models: -10 to 60°C (14 to 140°F)
     Wide Temp. Models: -40 to 75°C (-40 to 167°F)
     Storage Temperature: -40 to 85°C (-40 to 185°F)
Ambient Relative Humidity: 5 to 95% (non-condensing)
Altitude: Up to 2000 m

Standards and Certifications

Safety: UL 508
EMI: EN 61000-3-2; EN 61000-3-3; EN 61000-6-4;
FCC Part 15, Subpart B, Class A
EMS: 
     EN 61000-4-2, EN 61000-4-3, EN 61000-4-4,
     EN 61000-4-5, EN 61000-4-6, EN 61000-4-8,
     EN 61000-4-11, EN 61000-6-2
Shock: IEC 60068-2-27
Freefall: IEC 60068-2-32
Vibration: IEC 60068-2-6
Green Product: RoHS, CRoHS, WEEE

Warranty

Warranty Period: 5 years (excluding ioLogik E2214*)
*Note: Because of the limited lifetime of power relays, products that use that component are covered by a 2-year warranty.