Moxa MGate 5103 1-port Modbus/EtherNet/IP to PROFINET gateway

Introduction

The MGate 5103 is an industrial Ethernet gateway for converting Modbus RTU/ASCII/TCP or EtherNet/IP to PROFINET-based network communications. To integrate existing Modbus devices onto a PROFINET network, use the MGate 5103 as a Modbus master/slave or EtherNet/IP adapter to collect data and exchange data with PROFINET devices. The latest exchange data will be stored in the gateway. The gateway will convert stored Modbus or EtherNet/IP data into PROFINET packets so the PROFINET IO Controller can control or monitor field devices.

Features and Benefits

•  Converts Modbus, or EtherNet/IP to PROFINET
•  Supports PROFINET IO device
•  Supports Modbus RTU/ASCII/TCP master/client and slave/server
•  Supports EtherNet/IP Adapter
•  Effortless configuration via web-based wizard
•  Built-in Ethernet cascading for easy wiring
•  Embedded traffic monitoring/diagnostic information for easy troubleshooting
•  microSD card for configuration backup/duplication and event logs
•  Status monitoring and fault protection for easy maintenance
•  Serial port with 2 kV isolation protection
•  -40 to 75°C wide operating temperature models available
•  Supports redundant dual DC power inputs and 1 relay output
•  Security features based on IEC 62443

Specifications

Ethernet Interface
10/100BaseT(X) Ports (RJ45 connector): 
 2
 Auto MDI/MDI-X connection
 
Magnetic Isolation Protection: 1.5 kV (built-in)
 
Ethernet Software Features
Industrial Protocols: PROFINET IO Device, Modbus TCP Client (Master), Modbus TCP Server (Slave), EtherNet/IP Adapter
Configuration Options:  Web Console (HTTP/HTTPS), Device Search Utility (DSU), Telnet Console
Management:  ARP, DHCP Client, DNS, HTTP, HTTPS, SMTP, SNMP Trap, SNMPv1/v2c/v3, TCP/IP, Telnet, SSH, UDP, NTP Client
MIB:  RFC1213, RFC1317
Time Management:  NTP Client
 
Serial Interface
Console Port:  RS-232 (TxD, RxD, GND), 8-pin RJ45 (115200, n, 8, 1)
No. of Ports: 1
Connector:  DB9 male
Serial Standards:  RS-232/422/485
Baudrate:  50 bps to 921.6 kbps
Data Bits:  7, 8
Parity:  None, Even, Odd, Space, Mark
Stop Bits:  1, 2
Flow Control:  RTS Toggle (RS-232 only), RTS/CTS
RS-485 Data Direction Control:  ADDC® (automatic data direction control)
Pull High/Low Resistor for RS-485:  1 kilo-ohm, 150 kilo-ohms
Terminator for RS-485:  120 ohms
Isolation:  2 kV (built-in)
 
Serial Signals
RS-232: TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
RS-422:  Tx+, Tx-, Rx+, Rx-, GND
RS-485-2w:  Data+, Data-, GND
RS-485-4w:  Tx+, Tx-, Rx+, Rx-, GND
 
Serial Software Features
Configuration Options: Serial Console
Industrial Protocols:  Modbus RTU/ASCII Master, Modbus RTU/ASCII Slave
 
Modbus RTU/ASCII
Mode: Master, Slave
Functions Supported:  1, 2, 3, 4, 5, 6, 15, 16, 23
Max. No. of Commands:  128
Input Data Size: 512 bytes
Output Data Size:  512 bytes